Hir High Bond Grey / White

  • Home
  • Hir High Bond Grey / White

INTRODUCTION

hir adhesives are innovated by R&D multi utility premix mortar that can be used for fixing tiles, stones, marbles, mosaic tiles and other big size tiles. For best results hir adhesives provide better bonding and curing with least shrinkage and cracking because of absence of impurities in raw material. Less water for making mixture comapare to regular cement. No curing required. No wastage of material and water. Easy to apply

Pack : 20kg

Colour : Grey / White

Hir High Bond Grey / White

hir high bond cement and is grey in colour and preffered for laying on floor and wall larger tiles and dark marbles and stone. Surface should be prepared before applying adhesive. no paints, wall putty or damaged wall surface for bonding and adhesion.

Application

 
 

CHARACTERISTICS

Parameter Hir High Bond Grey/White
Appearance Grey free flow powder
Pot Life 60 minutes
PH Alkaline
Required Water Ratio 27 to 29 %
Coverage @ 3 mm 2.30 sqft/Kg
Coverage @ 6 mm 1.15 sqft/Kg
Coverage @ 9 mm 0.75 sqft/Kg
Bulk Density 1600 - 1900 Kg/m3
Maximum Aggregate Size 1 mm
 

TECHNICAL SPECIFICATIONS

Parameter

Values#

Requirement
As Per IS-15477
Type - I

Requirement
As Per IS-15477
Type II

FixoBond
Type-
I
FixoBond +
Type-II

FixoBond Prime
Type-II

Tensile Adhesion
   Dry Condition 750 N - 850 N 900 N 900 N
   Wet Condition 450 N - 500 N 580 N 600 N
Shear Adhesion
   Dry Condition (24 Hrs.) 2.50 KN 4.00 KN 2.65 KN 4.50 KN 4.75 KN
   Dry Condition (14 Days) 8.00 KN 10.00 KN 8.25 KN 10.50 KN 11.00 KN
   Heat Aging Condition 4.00 KN 5.00 KN 4.05 KN 5.15 KN 6.00 KN
   Wet Condition 4.00 KN 5.00 KN 4.50 KN 5.50 KN 6.75 KN
Open Time - - 10 Minutes 20 Minutes 20 Minutes
Adjustment Time - - 5 Minutes 15 Minutes 20 Minutes
Foot Traffic - - 24 Hours 24 Hours 24 Hours

# The Values obtained are from our laboratory testing conditions. Tests conducted on site conditions may show slight variation due to methods of testing/application.

PREPARATION AND APPLICATION

Floor Base Preparation

Floor Surface where tile has to be fixed should be of concrete base, properly cured, leveled and free of cracks.

Wall Base Preparation

Wall Surface where tile has to be fixed should be of concrete base, properly cured, leveled and free of cracks.

Clean Surface

Clean surface by wire brush and ensure contamination-free area.

Mixing Tile Adhesive

Pour Hir Tile Adhesive into water as per required ratio.

Mixing

Mix the paste using hand mixer for 5 minutes.

Rest

Rest for 5-10 min and remix again for 2-3 min.

Floor Wetting

Floor Wet the surface and tile before application.

Wall Wetting

Wall Wet the surface and tile before application.

Apply

Apply adhesive on the wall/floor using trowel at a thickness of 3-6 mm and comb with notch trowel. Do not spread more than 1 sq. m of area at a time.

Fix Tiles

Fix tiles firmly into position with a sliding motion and hammer with soft mallet to ensure a better bond.

Cleaning Adhesive

Clean off excessive adhesive between the joints and on tiles with a damp cloth.

Leave To Dry

Do not disturb the tiling for minimum 24 hours.

 
 
Download Brochure